Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!
Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.

With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.

Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!


The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.

Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
×