Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here 

Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.

Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.


This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.

Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.

Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.


Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.


I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
Particleboard is a manufactured wood product composed of sawdust, wood chips or wood shavings mixed with a resin. This concoction is layered, compressed, subjected to heat and cut to shape, resulting in a sheet material that can be used for a variety of things. It’s often used as shelving or as an underlayment for carpet. Plastic laminate may be applied to both sides to create a product that can be used to create everything from furniture to cabinets to wall paneling. Head into IKEA and you’ll find acres of particleboard.
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones. 

I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
×