Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!

Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.


Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.

Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.[12]
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
When it comes to woodworking for beginners, there are 6 things that I think are essential to know for how to start woodworking. I’m going to discuss each of these tips in hopefully a really simple way to make it a breeze to understand, so you can get to the fun part of actually starting to woodwork! I wish when I started and was learning how to woodwork that I had a simple beginner tips guide like this one!
While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection. 

This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.

Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
×