Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.

Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.

With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project. 

Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.

Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.


Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished. 

The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.

woodworking projects

×