Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.

It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!

Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.
The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces 

This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.

If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.


Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​ 

Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]
There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate. 

Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!

We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Hardwoods are separated into two categories, temperate and tropical hardwoods, depending on their origin. Temperate hardwoods are found in the regions between the tropics and poles, and are of particular interest to wood workers for their cost-effective aesthetic appeal and sustainable sources.[9] Tropical hardwoods are found within the equatorial belt, including Africa, Asia, and South America. Hardwoods flaunt a higher density, around 65lb/cu ft as a result of slower growing rates and is more stable when drying.[9] As a result of its high density, hardwoods are typically heavier than softwoods but can also be more brittle.[9] While there are an abundant number of hardwood species, only 200 are common enough and pliable enough to be used for woodworking.[11] Hardwoods have a wide variety of properties, making it easy to find a hardwood to suit nearly any purpose, but they are especially suitable for outdoor use due to their strength and resilience to rot and decay.[9] The coloring of hardwoods ranges from light to very dark, making it especially versatile for aesthetic purposes. However, because hardwoods are more closely grained, they are typically harder to work than softwoods. They are also harder to acquire in the United States and, as a result, are more expensive.[9]

(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
×