This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it! 

This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.

Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.


For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable. 

Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.


Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13] 

(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});

Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.


Who doesn’t want to have one awesome and handy wooden desk organizer that not only looks beautiful but can store all your mini office desk items properly? See the picture below. I am sure you will love this one. I have already built one myself as I just could not resist having one at my office. This thing easily stores all my office desk essentials, including pen, pencils, marker, small notebooks, etc. in the most organized way. You can see it yourself.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster

Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.

We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it! 

Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip. 

Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster

Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
I recently came across this beautiful wooden swing set, which was made in the shape of a boat. Cool, isn’t it? The very first look was enough for me to start loving it. Although I haven’t yet tried building one myself, I am definitely going to. Later I realized that you can also build a baby cradle with the same idea. After all, what can be more calming than the tender rocking of a boat? This swing set will surely help your child get more gentle sleep.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.

Woodworking was essential to the Romans. It provided, sometimes the only, material for buildings, transportation, tools, and household items. Wood also provided pipes, dye, waterproofing materials, and energy for heat.[5]:1Although most examples of Roman woodworking have been lost,[5]:2 the literary record preserved much of the contemporary knowledge. Vitruvius dedicates an entire chapter of his De architectura to timber, preserving many details.[6] Pliny, while not a botanist, dedicated six books of his Natural History to trees and woody plants, providing a wealth of information on trees and their uses.[7]
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
×