The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular ﬁnishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each ﬁnish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and ﬁnish combinations. Plus: How to stain wood evenly.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.